Skip to content

Bring a demoted primary site back online

DETAILS: Tier: Premium, Ultimate Offering: Self-managed

After a failover, it is possible to fail back to the demoted primary site to restore your original configuration. This process consists of two steps:

  1. Making the old primary site a secondary site.
  2. Promoting a secondary site to a primary site.

WARNING: If you have any doubts about the consistency of the data on this site, we recommend setting it up from scratch.

Configure the former primary site to be a secondary site

Since the former primary site is out of sync with the current primary site, the first step is to bring the former primary site up to date. Note, deletion of data stored on disk like repositories and uploads is not replayed when bringing the former primary site back into sync, which may result in increased disk usage. Alternatively, you can set up a new secondary GitLab instance to avoid this.

To bring the former primary site up to date:

  1. SSH into the former primary site that has fallen behind.

  2. Remove /etc/gitlab/gitlab-cluster.json if it exists.

    If the site to be re-added as a secondary site was promoted with the gitlab-ctl geo promote command, then it may contain a /etc/gitlab/gitlab-cluster.json file. For example during gitlab-ctl reconfigure, you may notice output like:

    The 'geo_primary_role' is defined in /etc/gitlab/gitlab-cluster.json as 'true' and overrides the setting in the /etc/gitlab/gitlab.rb

    If so, then /etc/gitlab/gitlab-cluster.json must be deleted from every Sidekiq, PostgreSQL, Gitaly, and Rails node in the site, to make /etc/gitlab/gitlab.rb the single source of truth again.

  3. Make sure all the services are up:

    sudo gitlab-ctl start

    NOTE: If you disabled the primary site permanently, you need to undo those steps now. For distributions with systemd, such as Debian/Ubuntu/CentOS7+, you must run sudo systemctl enable gitlab-runsvdir. For distributions without systemd, such as CentOS 6, you need to install the GitLab instance from scratch and set it up as a secondary site by following Setup instructions. In this case, you don't need to follow the next step.

    NOTE: If you changed the DNS records for this site during disaster recovery procedure you may need to block all the writes to this site during this procedure.

  4. Set up Geo. In this case, the secondary site refers to the former primary site.

    1. If PgBouncer was enabled on the current secondary site (when it was a primary site) disable it by editing /etc/gitlab/gitlab.rb and running sudo gitlab-ctl reconfigure.
    2. You can then set up database replication on the secondary site.

If you have lost your original primary site, follow the setup instructions to set up a new secondary site.

Promote the secondary site to primary site

When the initial replication is complete and the primary site and secondary site are closely in sync, you can do a planned failover.

Restore the secondary site

If your objective is to have two sites again, you need to bring your secondary site back online as well by repeating the first step (configure the former primary site to be a secondary site) for the secondary site.

Restoring additional secondary sites

If there is more than one secondary site, the remaining sites can be brought online now. For each of the remaining sites, initiate the replication process with the primary site.

Skipping re-transfer of data on a secondary site

When a secondary site is added, if it contains data that would otherwise be synced from the primary, then Geo avoids re-transferring the data.

  • Git repositories are transferred by git fetch, which only transfers missing refs.
  • Geo's container registry sync code compares tags and only pulls missing tags.
  • Blobs/files are skipped if they exist on the first sync.

Use-cases:

  • You do a planned failover and demote the old primary site by attaching it as a secondary site without rebuilding it.
  • You have multiple secondary Geo sites. You do a planned failover and reattach the other secondary Geo sites without rebuilding them.
  • You do a failover test by promoting and demoting a secondary site and reattach it without rebuilding it.
  • You restore a backup and attach the site as a secondary site.
  • You manually copy data to a secondary site to workaround a sync problem.
  • You delete or truncate registry table rows in the Geo tracking database to workaround a problem.
  • You reset the Geo tracking database to workaround a problem.

Skipping re-transfer of blobs or files

FLAG: On self-managed GitLab, by default this feature is available. On GitLab.com and GitLab Dedicated, this feature is not available.

When you add a secondary site which has preexisting file data, then the secondary Geo site will avoid re-transferring that data. This applies to:

  • CI job artifacts
  • CI pipeline artifacts
  • CI secure files
  • LFS objects
  • Merge request diffs
  • Package files
  • Pages deployments
  • Terraform state versions
  • Uploads
  • Dependency proxy manifests
  • Dependency proxy blobs

If the secondary site's copy is actually corrupted, then background verification will eventually fail, and the file will be resynced.

Files will only be skipped in this manner if they do not have a corresponding registry record in the Geo tracking database. The conditions are strict because resyncing is almost always intentional, and we cannot risk mistakenly skipping a transfer.